14MPa Position Sensing Hydraulic Cylinder/Double-acting Single-rod(with switch) PTH-1BR
Description of Term
Product Lineup
Working Fluids Action Style Bore Size mm
50 63 80 100 125 140 150 160 180 200 224 250
Double-acting Single-rod
with switch
B Rod 価格についてはお問合せください。 価格についてはお問合せください。 価格についてはお問合せください。 価格についてはお問合せください。 価格についてはお問合せください。 価格についてはお問合せください。 - - - - - -

Action Style Double-acting Single-rod/with switch
Available Bores(mm) φ50·φ63·φ80·φ100·φ125·φ140
Mounting Style SD·LA·FY·TA·TC style
Rod diameter type B Rod
Nominal Pressure 14MPa
Max. AllowablePressure 18MPa
Proof Test Pressure 21MPa
Min. Working
Rod Side 0.45MPa and below
Head Side 0.3MPa and below
Operating Speed Range φ50·φ63:8∼400mm/s  φ80∼φ125:8∼300mm/s
Temperature Range -10∼+80ºC (But do not use wnen frozen)
Structure of Cushioning Metal fitting type
Working Fluid Petroleum-based fluid
(For other working oil, refer to the table of working oil adaptability.)
Tolerance of Thread JIS 6g/6H
Stroke Tolerance
Accessories Rod End Attachments Rod End Attachments(Single-clevis (T-end))·(Double-clevis (Y-end))·Floating joint (F-end)
Rod Boot Standard:Nylon tarpaulin Semi-standard:Chloroprene·Conex
Others Lock nut
Note) Hydraulic pressure that is generated in cylinder due to the inertia of load shall be set at less than the maximum allowable pressure.
Note) There is a hole with φ13∼φ16 right through the piston rod. Please be noted that there may be oil leak if the piston rod get damaged when a set screw is fixed.
Note) Do not loosen the flange of rod end. The oil may blust out.
Note) Temperature range is different depend on the packing material. Please refer to the selection material.
Note) If using lock nut at the end of piston rod, please order to lengthen the thread length of piston rod end (A dimension).
Note) Conex of boots is the registered trade mark of Teijin,Ltd.

Specifications of Detector
Power supply DC24V±2V 0.05A
Accuracy Linearity ±0.025%FS or ±75μmTYP
Resolution Ability ±0.01%FS or ±30μm and below
Repeatability ±0.01%FS or ±30μm and below
Temperature Character 40ppmFS/ºC or12μm/ºC and below
Output Current output 4∼20mA Load resistance 500Ω and below
Consult for voltage output (0∼10V etc.)
Frequency characteristic Scanning frequency 1kHz
Temperature Range -20ºC ∼+80ºC (But do not use wnen frozen)
Impact-resistant 50G 2m/s
Vibration-resistant 6G or 40Hz2mmPP
Protective structure IP67 (10kPa, 30min)
Note) Above specification is based on a single detector.
Note) The accuracy value is the large value which mentioned beside.
Note) When the detector is fixing on a cylinder, the accuracy mentioned above may be different depending on the pressure and load which may deformed the parts of cylinder. The repeatability accuracy at a same situation may get a similar value as mentioned above.
Note) The output at retracted end is 4.0∼4.5mA or 0∼0.3V, and at extended end is 12∼20mA or 5∼10V. (There may be some parts of effective length of sensor is not available depending on the stroke) Please set the controller based on the output of actual extended end and retracted end.
Note) Please consult for extend/retract end output adjustable sensor type.

Compatibility of Working Fluid and Packing Material
Material Working Fluids
Water in Oil
Oil in Water
1:Nitrile rubber
2:Urethane rubber
3:Fluoric rubber
Note1) The and -marked items are applicable, while -marked items are inapplicable. Please contact to us when you use -marked items.
Note2) The -marked items are the recommended packing materials in case of the first priority to abrasion resistance.

Copyright(c)2004 TAIYO,LTD. All rights reserved.