 |
 |
Product Lineup |
|
Working Fluids |
Action Style |
Bore Size mm |
50 |
63 |
80 |
100 |
125 |
140 |
150 |
160 |
180 |
200 |
224 |
250 |
Double-acting Single-rod
Standard |
B Rod |
 |
 |
 |
 |
 |
 |
 |
 |
 |
 |
 |
 |
|
 |
Specifications |
Action Style |
Double-acting Single-rod/Standard |
Available Bores(mm) |
φ50·φ63·φ80·φ100·φ125·
φ140·φ150·φ160·φ180·φ200·φ240·φ250 |
Mounting Style |
SD·LA·FY·TA·TC形 |
Rod diameter type |
B Rod |
Nominal Pressure |
14MPa |
Max. AllowablePressure |
18MPa |
Proof Test Pressure |
21MPa |
Min. Working Pressure |
Rod Side |
0.45MPa and below |
Head Side |
0.3MPa and below |
Operating Speed Range |
φ50·φ63:8∼400mm/s φ80∼φ125:8∼300mm/s
φ140∼φ250:8∼200mm/s |
Temperature Range |
-10∼+80ºC (But do not use wnen frozen) |
Structure of Cushioning |
Metal fitting type |
Working Fluid |
Petroleum-based fluid
(For other working oil, refer to the table of working oil adaptability.) |
Tolerance of Thread |
JIS 6g/6H |
Stroke Tolerance |
 |
Accessories |
Rod End Attachments |
Rod End Attachments(Single-clevis (T-end))·(Double-clevis (Y-end))·Floating joint (F-end) |
Rod Boot |
Standard:Nylon tarpaulin Semi-standard:Chloroprene·Conex |
Others |
Lock nut |
Note) |
Hydraulic pressure that is generated in cylinder due to the inertia of load shall be set at less than the maximum allowable pressure. |
Note) |
There is a hole with φ13∼φ16 right through the piston rod. Please be noted that there may be oil leak if the piston rod get damaged when a set screw is fixed. |
Note) |
Do not loosen the flange of rod end. The oil may blust out. |
Note) |
Temperature range is different depend on the packing material. Please refer to the selection material. |
Note) |
If using lock nut at the end of piston rod, please order to lengthen the thread length of piston rod end (A dimension). |
Note) |
Conex of boots is the registered trade mark of Teijin,Ltd. |
 |
Specifications of Detector |
Power supply |
DC24V±2V 0.05A |
Accuracy |
Linearity |
±0.025%FS or ±75μmTYP |
Resolution Ability |
±0.01%FS or ±30μm and below |
Repeatability |
±0.01%FS or ±30μm and below |
Temperature Character |
40ppmFS/ºC or12μm/ºC and below |
Output |
Current output 4∼20mA Load resistance 500Ω and below
Consult for voltage output (0∼10V etc.) |
Frequency characteristic |
Scanning frequency 1kHz |
Temperature Range |
-20ºC ∼+80ºC (But do not use wnen frozen) |
Impact-resistant |
50G 2m/s |
Vibration-resistant |
6G or 40Hz2mmPP |
Protective structure |
IP67 (10kPa, 30min) |
Note) |
Above specification is based on a single detector. |
Note) |
The accuracy value is the large value which mentioned beside. |
Note) |
When the detector is fixing on a cylinder, the accuracy mentioned above may be different depending on the pressure and load which may deformed the parts of cylinder. The repeatability accuracy at a same situation may get a similar value as mentioned above. |
Note) |
The output at retracted end is 4.0∼4.5mA or 0∼0.3V, and at extended end is 12∼20mA or 5∼10V. (There may be some parts of effective length of sensor is not available depending on the stroke) Please set the controller based on the output of actual extended end and retracted end. |
Note) |
Please consult for extend/retract end output adjustable sensor type. |
 |
Compatibility of Working Fluid and Packing Material |
Material |
Working Fluids |
Petroleum-based
Fluid |
Water-Glycol
Fluid |
Phosphate-Ester
Fluid |
Water in Oil
Fluid |
Oil in Water
Fluid |
1:Nitrile rubber |
 |
 |
 |
 |
 |
2:Urethane rubber |
 |
 |
 |
 |
 |
3:Fluoric rubber |
 |
 |
 |
 |
 |
6:HNBR |
 |
 |
 |
 |
 |
Note1) |
The and -marked items are applicable, while -marked items are inapplicable. Please contact to us when you use -marked items. |
Note2) |
The -marked items are the recommended packing materials in case of the first priority to abrasion resistance. |
|
|
|
|