 |
 |
Product Lineup |
  Click the icon as follows, to check the details.
|
| Rod End Type |
Bore Size(mm) |
| 20 |
25 |
32 |
40 |
50 |
63 |
| Female |
|
|
|
|
|
|
| Male |
|
|
|
|
|
|
|
|
Specifications |
| Action Style |
Double-acting Single-rod/Basic |
| Available Bores(mm) |
 20,25,32,40,50,63 |
| Mounting Style |
SD |
| Rod End Type |
Female/Male |
| Norminal Pressure |
3.5MPa |
| Max. Allowable Pressure |
4MPa |
| Min. Working Pressure |
20/25/32:0.15MPa 40/50/63:0.1MPa |
| Proof Test Pressure |
5MPa |
| Operating Speed Range |
8 to 100mm/s |
Operating Temperature
(Ambient Temperature and Oil Temperature) |
-10 to +70 ºC(But do no use when frozen) |
| Cushion Mechanism |
None |
| Working Fluid |
Petroleum-based fluid
(For other working oil, refer to the table of working
oil adaptability.) |
| Thread Tolerance |
JIS 6H/6g |
| Stroke Tolerance |
0 to 1.0mm |
Note)
|
Hydraulic pressure that is generated in cylinder dur to the inertia of load shall be set at less than the maximum allowable pressure. |
|
The main body of cylinder is not cutting oil proof specification. |
|
This cylinder is not equipped with an air bleeder. |
|
If the piston touches the cylinder end at the stroke end, decelerate the
cylinder to a speed lower than the minimum operating speed. |
|
Stroke Fabrication Range |
|
Bore
(mm) |
Cylinder Stroke(mm) |
| 5 |
10 |
15 |
20 |
25 |
30 |
35 |
40 |
45 |
50 |
60 |
70 |
80 |
90 |
100 |
| 20 |
 |
|
|
|
|
|
|
|
|
|
- |
- |
- |
- |
- |
| 25 |
|
|
|
|
|
|
|
|
|
|
|
- |
- |
- |
- |
| 32 |
|
|
|
|
|
|
|
|
|
|
|
|
|
- |
- |
| 40 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| 50 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| 63 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| Note1) |
Consult to factory when you request stroke out of standard. |
Note2)
|
Avoid use of a cylinder in such a manner that eccentric load applies to the cylinder. When you use of mounting accessories of rotary type is intended in particular, be sure to consult to us in advance. |
|
|
|
Allowable Fluid, Seal Material |
| Seal Material |
Nonaqueous Cutting Oil |
| Petroleum-based Fluid |
Water-Glycol Fluid |
Phosphate-Ester Fluid |
Water in Oil Fluid |
Oil in Water Fluid |
| 6: HNBR |
|
|
 |
|
|
Note)
|
| The -marked items are applicable, while -marked items are
inapplicable. |
Consult to factory when you request to use Phosphate-Ester Fluid. |
|
|
