 |
 |
Product Lineup |
  Click the icon as follows, then the price and |
| Rod End Type |
Bore(mm) |
| 32 |
40 |
50 |
63 |
80 |
| Female |
|
|
|
|
|
| Male |
|
|
|
|
|
|
|
Specifications |
| Action Style |
Double-acting Single-rod/Switch Set |
| Available Bores(mm) |
 32/40/50/63/80 |
| Mounting Style |
SD |
| Rod End Type |
Female/Male |
| Norminal Pressure |
21MPa |
| Max. Allowable Pressure |
216MPa |
| Proof Test Pressure |
31.5MPa |
| Min. Working Pressure |
0.3MPa |
Operating Temperature
(Ambient Temperature and Oil Temperature) |
-10 to +170 ºC(But, do not use when frozen)
Note)When using the AX125/AZ125 swithces, use it up to 100 ºC. |
| Structure of Cushioning |
None |
| Working Fluid |
Petroleum-based fluid
(For other working oil, refer to the tableof working oil adaptability.) |
| Thread Tolerance |
JIS 6H/6g |
| Stroke Tolerance |
0 to 0.8mm |
| Note) |
Hydraulic pressure that is generated in cylinder dur to the inertia of load shall be set at less than the maximum allowable pressure. |
|
This cylinder is not equipped with an air bleeder. |
|
Since lateral load (eccentric load) cannot be applied to the piston rod, carefully adjust it after rod end attachment. |
|
If the piston touches the cylinder end at the stroke end, decelerate the cylinder to a speed lower than the minimum operating speed. |
|
Stroke Fabrication Range |
|
Bore
(mm) |
Cylinder Stroke(mm) |
| 5 |
10 |
15 |
20 |
25 |
30 |
40 |
50 |
60 |
70 |
80 |
| 32 |
 |
|
|
|
|
|
|
|
|
|
|
| 40 |
|
|
|
|
|
|
|
|
|
|
|
| 50 |
|
|
|
|
|
|
|
|
|
|
|
| 63 |
|
|
|
|
|
|
|
|
|
|
|
| 80 |
|
|
|
|
|
|
|
|
|
|
|
|
| Note1) |
: Standard manufacturing range |
|
|
|
Switch Mounting Min. Possible Stroke |
|
| Bore(mm) |
1 switch mounted |
2 switches mounted |
| 32 |
5 |
10 |
| 40 |
| 50 |
| 63 |
| 80 |
| Note1) |
There may cause interference with switch. Please adjust when one contact
switch is used in the case of 10mm stroke. |
|
Please use two locations on the switch mounting channel when the no-contact
switch is used in the case of 10mm stroke. |
|
Allowable Fluid, Seal Material |
| Seal Material |
Allowable Fluid |
| Petroleum-based Fluid |
Watar-Glycol Fluid |
Phoshate-Ester Fluid |
Water in Oil Fluid |
Oil in Water Fluid |
| 3: Fluoric Rubber |
|
 |
|
|
|
| 6: HNBR |
 |
|
|
|
|
| Note) |
The and -marked items are applicable, while -marked items are inapplicable. |
|
The -marked items are the recommended packing materials in case of giving
the first priority to abrasion resistance. |
|
|
