 |
 |
Product Lineup |
 Click the icon as follows, then the price and  |
| Mounting Style |
Rod End Type |
Bore(mm) |
| 20 |
25 |
32 |
40 |
50 |
63 |
80 |
100 |
125 |
| SD |
Female |
- |
- |
|
|
|
|
|
- |
- |
| Male |
- |
- |
|
|
|
|
|
- |
- |
| LD/FA |
Female |
- |
- |
|
|
|
|
|
- |
- |
| Male |
- |
- |
|
|
|
|
|
- |
- |
|
|
Specifications |
| Action Style |
Double-acting Double-rod/Switch set |
| Available Bores(mm) |
 32/40/50/63/80 |
| Mounting Style |
SD/LA/LD/FA |
| Rod End Type |
Female/Male |
| Norminal Pressure |
16MPa |
| Max. Allowable Pressure |
16MPa |
| Proof Test Pressure |
24MPa |
| Min. Working Pressure |
0.3MPa |
| Operating Speed Range |
8 to 100mm/s |
Operating Temperature
(Ambient Temperature and Oil Temperature) |
-10 to +120 ºC(But do not use when frozen) |
| Structure of Cushioning |
None |
| Working Fluid |
Petroleum-based fluid
(For other working oil, refer to the tableof working oil adaptability.) |
| Thread Tolerance |
JIS 6H/6g |
| Stroke Tolerance |
0 to 0.8mm |
| Note) |
Hydraulic pressure that is generated in cylinder dur to the inertia of
load shall be set at less than the maximum allowable pressure. |
|
This cylinder is not equipped with an air bleeder. |
|
Since lateral load (eccentric load) cannot be applied to the piston rod,
carefully adjust it after rod end attachment. |
|
If the piston touches the cylinder end at the stroke end, decelerate the
cylinder to a speed lower than the minimum operating speed.ピ |
|
Stroke Fabrication Range |
|
Bore
(mm)) |
Cylinder Stroke(mm) |
| 5 |
10 |
15 |
20 |
25 |
30 |
35 |
40 |
45 |
50 |
60 |
70 |
80 |
90 |
100 |
| 32 |
 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| 40 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| 50 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| 63 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| 80 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| Note1) |
:Range available for manufacturing for order |
|
|
|
Switch Mountable Minimum Stroke |
|
Bore
(mm) |
1switch mounted |
2 switches mounted |
| AX/AZ |
WR |
WS |
AX/AZ |
WR |
WS |
| 32 |
5 |
5 |
10 |
10 |
10 |
20 |
| 40 |
| 50 |
| 63 |
| 80 |
| Note1) |
When attaching two swithces of the WR or WS type, they cannot be attached to the same surfice.(WR and WD type switches are not available for LA mounting.) |
|
There may cause interference with switch. Please adjust when one contact switch is used in the case of 10mm stroke. |
|
Please use two locations on the switch mounting channel when the no-contact switch is used in the case of 10mm stroke. |
|
Allowable Fluid, Seal Material |
| Seal Material |
Allowable Fluid |
| Petroleum-based Fluid |
Watar-Glycol Fluid |
Phoshate-Ester Fluid |
Water in Oil Fluid |
Oil in Water Fluid |
| 3: Fluoric rubber |
 |
 |
|
|
|
| 6: HNBR |
 |
|
|
|
|
| Note) |
The and -marked items are applicable, while -marked items are inapplicable |
|
The -marked items are the recommended packing materials in case of the first priority to abrasion resistance. |
|
|
