 |
 |
Product Lineup |
  Click the icon as follows, to check the details.
out |
| Mounting Style |
Rod End Type |
Bore Size(mm) |
| 20 |
25 |
32 |
40 |
50 |
63 |
80 |
100 |
125 |
| SD |
Female |
- |
- |
|
|
|
|
|
|
- |
| Male |
- |
- |
|
|
|
|
|
|
- |
| LD/FA/FB |
Female |
- |
- |
|
|
|
|
|
- |
- |
| Male |
- |
- |
|
|
|
|
|
- |
- |
|
|
Specifications |
| Action Style |
Cutting flruid proof type/Double-acting Single-rod/Standard Type |
| Available Bores(mm) |
 32/40/50/63/80/100 |
| Mounting Style |
SD/LD/FA/FB |
| Rod End Tyle |
Female/Male |
| Norminal Pressure |
16MPa |
| Max. Allowable Pressure |
16MPa |
| Proof Test Pressure |
24MPa |
| Min. Working Pressure |
0.3MPa |
| Operating Speed Range |
8 to 100mm/s |
Operating Temperature
(Ambient Temperature and Oil Temperature) |
-10 to +120 ºC(But no freezing allowed) |
| Structure of Cushioning |
None |
| Working Fluid |
Petroleum-based fluid
(For other working oil, refer to the tableof working oil adaptability.) |
| Thread Tolerance |
JIS 6H/6g |
| Stroke Tolerance |
0 to 0.8mm |
| Note) |
Hydraulic pressure that is generated in cylinder dur to the inertia of
load shall be set at less than the maximum allowable pressure. |
|
This cylinder is not equipped with an air bleeder. |
|
Since lateral load (eccentric load) cannot be applied to the piston rod,
carefully adjust it after rod end attachment. |
|
If the piston touches the cylinder end at the stroke end, decelerate the
cylinder to a speed lower than the minimum operating speed. |
|
Stroke Fabrication Range |
|
| Mounting Style |
Bore Size
(mm) |
Cylinder Stroke(mm) |
| 5 |
10 |
15 |
20 |
25 |
30 |
35 |
40 |
45 |
50 |
60 |
70 |
80 |
90 |
100 |
| SD |
32 |
 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| 40 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| 50 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| 63 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| 80 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| 100 |
 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
LD
FA
FB |
32 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| 40 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| 50 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| 63 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| 80 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| Note1) |
:Range available for manufacturing for order |
|
|
|
Allowable Fluid, Seal Material |
| Seal Material |
Nonaqueous Cutting Oil |
Aqueous Cutting Oil |
| Type 1 |
Type 2 |
| 6: HNBR |
|
 |
|
| Note) |
| The -marked items are applicable, while -marked items are
inapplicable. |
|
|
|
