New Products

ESG2 Series Electric Gripper

Comparable to the cost of pneumatic grippers!

more
Grease Suction Unit

Only air supply needed to start suction

more

Catalog

  • 21MPa Compact Hydraulic Cylinder

    210C-2 series
    • More compact than 210C-1 series.
    • Compact hydraulic cylinders with bores of φ40 to φ250 mm for use at pressures of 21MPa.
    • Switch set and Double-rod type are also available.
    • Cushion performance and Check valve performance improved.
    Specifications:
    Bore(mm)
    φ40,φ50,φ63,φ80,φ100,φ125,φ140,φ160,φ180,φ200,φ224,φ250
    Nominal pressure
    21MPa
    Types
    Double acting single rod, double rod, standard, switch set

    21MPa Hydraulic Cylinder

    210H-5 series
    • General hydraulic cylinders with bores of φ40 to φ160 mm for use at pressures of 21MPa.
    • More light and compact than 210H-3 series.
    • Cushion performance and Check valve perdormance improved.
    Specifications:
    Bore(mm)
    φ40,φ50,φ63,φ80,φ100,φ125,φ140,φ160
    Nominal pressure
    21MPa
    Types
    Double acting single rod, standard

    16MPa Compact & Short Tie-Rod Hydraulic Cylinder

    160ST-1 series
    • Full line with various bore sizes(φ32 to φ250) double-acting compact hydraulic cylinder.
    • Installation pitch is almost same as compact cylinder 160S-1 series, and it realized the same space saving as compact cylinder.
    • The large bore size 100mm to 250mm are standardized which are not avaiable in compact cylinder.
    Specifications:
    Bore(mm)
    φ32,φ40,φ50,φ63,φ80,φ100,φ125,φ140,φ160,φ180,φ200,φ224,φ250
    Nominal pressure
    16MPa
    Types
    Double acting single rod, standard, switch set
  • Compact design Guides Cylinder

    10G-2 series
    • Two guide rods plus the cylinder provides high rigidity and improved non-rotation accuracy position-setting accuracy.
    • Two types of bearings, sliding bearings and linear guide bushing bearings, are employed so they can be used accroding to the application, such as cses when they will be subject to horizontal loading or impact, or cases requiring high-accuracy posotioning.
    • Three types are available: Stopper type, lift type, and pusher type. Since it can be attached at the bottom of the body and a T-groove is provided on the side to allow direct attachment, it can be attached in even smaller spaces.
    Specifications:
    Bore(mm)
    φ20,φ32,φ40,φ50,φ63,φ80
    Operating pressure range
    0.1~1MPa
    Types
    Stopper type, lift type, pushre type

    Slide Unit

    TS series
    • Ideal for use as the workpiece conveyor for assembly robots where high positioning accuracy is required.
    • Space-saving actuator with double rods on both sides provides high accuracy, high drive speed, and high output force.
    Specifications:
    Bore(mm)
    φ10,φ16,φ25,φ32
    Operationg pressure
    1MPa
    Mounting methods
    Body fixed type, Plate fixed type
    Types
    Fundamental, with switch, with long stopper bolt, with shock absorber

    Rodless Cylinder (Band type)

    BL6 series
    • New guide variations were added.
    • Add bore size φ10 to internal guide type.
    • Supports a wide range of speed.
    • Guide variations enables to choose the optimum load carrying capacity.
    Specifications:
    Bore(mm)
    φ10,φ16,φ25,φ32,φ40,φ50,φ63,φ80
    Operationg pressure
    0.15~0.8MPa
    Types
    internal guide type, body guide type, plain bearing guide type, needle bearing guide type, roller guide type, ball bearing guide type
  • Electric Driven Diaphragm Pump

    ETD2 series
    • The cut of running costs and emissions of carbon dioxide to approx. 80% of that of the conventional company products.
    • Non exhaust of air operation keeps noise and emission at lower level.
    • Stable output rate driven by electrical motor.
    • Stable operation free from an effect of compressed air's fluctuation.
    • Add variations of flameproof and increased safety specification to the series.
    • We prepare also the separate type which easy for maintenance.
    Specifications:
    Port size
    Rc3/4, Rc1
    Motor Power
    0.4, 0.75, 1.5kW
    Maximum output rate
    18~120L/min

    ATSUKAN Servo

    PQCS2 series
    • Intelligent energy saving hydraulic system.
    • Whole hydraulic system is packed as single unit.
    • Combining high power, high accuracy and high efficiency.
    • No piping erection is necessary.
    • Load judging controller can be set up as an optional system.
    Specifications:
    Bore(mm)
    φ50,φ63,φ80,φ100
    Sensors
    Load cell, position sensor

    AC Servo Nut Runner

    ENRZ series
    • Downsized, lignt-weight, high-speed type nut runner.
    • You can choose the best method of system according to the conditions. Torque Control Time Monitor, Torque Control Angle Monitor, Imaginary Angle Method, Yield Method and the many other functions are exist.
    • When Master Controller is used, the data communication and the operation control can be effected only by the serial communication without using PIO.(Saving of Wiring)
    • The Console Display Unit(Touch Panel)is employed for central management of the multi-spindle system.
    Specifications:
    Tool Unit
    Maximum fastening Torque:2~800N・m
    Motor output:100~400W
    Control Unit
    Power supply:AC200~230V±10%
    Display:touch panel system
  • Air Balancer

    TMA series
    • Easy operation and excellent workability.
    • Support for handling various works.
    • Support for 5kg - 1000kg hoisting loads.
    • Flexible combination of equipment style and operation circuit for working condition.

    Vacuum Suction Equipment

    Specifications:
    Full line of vacuum suction equipment:
    Vacuum pads, vacuum units, pump units, valve units, ventury series, vacuum hoists

    Grease Suction Unit

    GVC-UN series
    • Grease Suction Unit for replacing grease.
    • Only air supply needed to start suction.
    • Portable, convenient.
    • Larger suction amount due to suction and pressurizing.
    Specifications:
    Grease type(consistency)
    No.0 , No.00
    Power supply
    Air pressure 0.5 to 0.7MPa
    Working temperature range
    +10~+50℃
    Degree of vacuum
    -93kPa (at air pressure of 0.5MPa)
  • Mini-Softer

    MA series
    • Long life time owing to special seal technology and high strength parts.
    • Adjustable type with two (front/rear) adjusters.
    • New design bladder accumulator comes off long life time.
    • Piston ring for all types.
    • Excessive energy absorption is possible for the emergency use.
    Specifications:
    Maximum energy absorption
    170~6100J
    Stroke
    23.1~150.1mm
    Maximum equivalent load
    9~79300kg
    Maximum resisting force value
    11570~58270N

    Mini-Softer/Self-Compensation

    F7M※,F8M※ series
    • Reacts to load variations so adjustment is not necessary.
    • Construction is simple and solid, and it reacts to the load without adjustment to softly stop the impact abject.
    Specifications:
    Applicable series:
    F7M08,F7M10,F7M12,F7M14,F7M16,F7M20,F7M25,F8M30,F8M36

    Dyna-Softer

    AS series
    • Can be adjusted steplessly within the maximum energy range.
    Specifications:
    Applicable series:
    AS※-06 series:Energy absorption:98.1~353J
    AS※-11 series: Energy absorption:676.7~1353.3J
    AS※-20 series:Energy absorption:2124.1~6384.1J

    Order-Made Specifications

    AS series
    • Standard Type S series, Heavy-Duty Type H series Order-made series designed and manufactured according to customer specifications.
    Specifications:
    Applicable series:
    S※※-0.6,S※※-11,S※※-20,S※※-40